Radyne OM20 Specifications Page 111
- Page / 183
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
DMD1050 Satellite Modem Board Web Browser
TRACKING RATE {0.5 to 6.0}
Allows the user to set the rate at which the commands to increase
or decrease Transmit Power are sent. Each command will result
in a 0.5 dB increase or decrease in Transmit Power from the
remote transmitter. The tracking rate is adjustable from 0.5 dB
per minute to 6.0 dB per minute in 0.5 dB steps. (Only
available when EFAUPC is selected as the framing)
LOCAL CL ACTION {HOLD, NOMINAL, MAXIMUM}
This allows the user to set the Remote Transmit Power Setting to
be used when the local modem receiver loses lock. The setting
can be 'HOLD' (no action taken), 'NOMINAL' (the nominal
Transmit Power Setting is used), and 'MAXIMUM' (the
maximum Transmit Power Setting is used). (Only available
when EFAUPC is selected as the framing)
REMOTE CL ACTION {HOLD, NOMINAL, MAXIMUM}
This allows the user to set the Local Transmit Power Setting to
be used when the remote modem receiver loses lock. The setting
can be 'HOLD' (no action taken), 'NOMINAL' (the nominal
Transmit Power Setting is used), and 'MAXIMUM' (the
maximum Transmit Power Setting is used).
REMOTE AUPC (menu) The 'REMOTE AUPC CONFIGURATION' Menu contains the
remote configuration parameters for the AUPC Function.
Remote AUPC menus are only available when modem is
configured for EF AUPC
AUPC MODE {DISABLE, EFDATA}
Allows the user to enable or disable the AUPC Function of the
remote modem. The remote AUPC Function is the response of
the local modem to commands for an increase or decrease of the
Transmit Power in 0.5 dB steps and the command to change to
the setting indicated in the 'REMOTE CL ACTION' Menu of the
remote modem upon receiver loss of lock.
LOOPBACK {DISABLE, ENABLE}
Allows the user to enable or disable the Baseband Loopback Test
Mode of the remote modem.
TX 2047 TEST {DISABLE, ENABLE}
Allows the user to enable or disable the Transmit 2047 Pattern
Test Mode of the remote modem.
RX 2047 BER: Reports the BER measurement of the receiver 2047 Pattern Test
Mode of the remote modem. BER is reported from the 1x10
-5
to
1x10
-7
in tenth decade steps. If the pattern does not synchronize
or is out of range, ‘NO DATA’ will be displayed.
When modems are configured for Radyne AUPC, the remote Eb/No will be
displayed in the Monitor Menus.
IMPORTANT
MN-DMD1050 7–21
Revision 9
- DMD1050 1
- Table of Contents 5
- PREFACE 11
- Warranty Policy 12
- Limitations of Warranty 12
- Exclusive Remedies 13
- Customer Support 14
- Chapter 1. Introduction 15
- 1.2 DMD1050 Configurations 16
- 1.2.2 Feature Upgrades 16
- 1.3 Function Accessibility 16
- Chapter 2. Installation 17
- 2.2 Unpacking 18
- 2.3 Removal and Assembly 18
- MN-DMD1050 2–3 19
- 2.6 Modulator Checkout 20
- 2.6.1 Initial Power-Up 20
- MN-DMD1050 2–5 21
- 2.7 Storage 22
- 3.1 DMD1050 Hardware 23
- MN-DMD1050 3–2 24
- MN-DMD1050 3–3 25
- 3.2.1 Baseband Processing 26
- MN-DMD1050 3–5 27
- 3.3.2 Terminal Mode Control 28
- MN-DMD1050 3–7 29
- 3.3.6 Terminal Screens 30
- MN-DMD1050 3–10 32
- 3.7.1.6 Ethernet QOS Type 33
- 3.7.1.7 Ethernet QOS Queue 33
- MN-DMD1050 3–12 34
- 3.7.1.9 Packet Statistics 35
- 3.8 Internal Clock 35
- MN-DMD1050 3–15 37
- MN-DMD1050 3–16 38
- 3.10.1 TX Clock Options 39
- 3.10.3 RX SAT Clock 41
- 3.12 Reed-Solomon Codec 42
- 3.12.3 Interleaving 43
- 3.13.1 Radyne AUPC 44
- 3.13.2 EF AUPC 45
- 3.13.3 Near Side AUPC 45
- MN-DMD1050 3–25 47
- MN-DMD1050 3–26 48
- MN-DMD1050 3–27 49
- MN-DMD1050 3–28 50
- 3.17.1 SCC Framing Structure 51
- 3.17.2 Aggregate Data Rate 52
- MN-DMD1050 3–31 53
- Example 1: 54
- Example 2: 54
- MN-DMD1050 3–33 55
- MN-DMD1050 3–34 56
- 3.19 Strap Codes 57
- MN-DMD1050 3–36 58
- 4.1 DMD1050 Connections 59
- MN-DMD1050 4–2 60
- MN-DMD1050 4–3 61
- MN-DMD1050 4–4 62
- MN-DMD1050 4–5 63
- MN-DMD1050 4–6 64
- MN-DMD1050 4–7 65
- MN-DMD1050 4–8 66
- MN-DMD1050 4–9 67
- MN-DMD1050 4–10 68
- CAUTION 69
- 5.2.1 Alarm Faults 70
- 5.2.1.1 Major Tx Alarms 70
- 5.2.1.2 Major Rx Alarms 70
- 5.2.1.3 Minor Tx Alarms 70
- 5.2.1.4 Minor Rx Alarms 71
- 5.2.1.5 Common Major Alarms 71
- 5.2.2 Alarm Masks 71
- Chapter 6. Technical 73
- Specifications 73
- MN-DMD1050 6–2 74
- 6.9.1 Non-DVB 75
- 6.9.2 DVB 76
- MN-DMD1050 6–5 77
- Viterbi 78
- Sequentia 79
- Trellis 81
- Viterbi Decoder 83
- MN-DMD1050 6–12 84
- MN-DMD1050 6–13 85
- MN-DMD1050 6–14 86
- MN-DMD1050 6–15 87
- MN-DMD1050 6–16 88
- MN-DMD1050 6–17 89
- 6.10.11 ACG Output Voltage 90
- Chapter 7. Web Browser 91
- 7.2.1 Appearance 92
- 7.2.2 Navigation 92
- 7.2.3 LED Indicators 93
- 7.3 GUI Screen Menus 94
- 7.3.1 Introduction Menu 95
- 7.3.1.1 Login Screen 96
- 7.3.2 Password Setup 97
- MN-DMD1050 7–8 98
- MN-DMD1050 7–9 99
- MN-DMD1050 7–10 100
- Revision 9 100
- MN-DMD1050 7–11 101
- MN-DMD1050 7–12 102
- Configuring the PC 103
- 7.3.4.1 Transmit Menu 104
- MN-DMD1050 7–15 105
- MN-DMD1050 7–16 106
- MN-DMD1050 7–17 107
- MN-DMD1050 7–18 108
- MN-DMD1050 7–19 109
- MN-DMD1050 7–20 110
- MN-DMD1050 7–21 111
- 7.3.4.2 Receive Menu 112
- MN-DMD1050 7–23 113
- MN-DMD1050 7–24 114
- MN-DMD1050 7–25 115
- MN-DMD1050 7–26 116
- MN-DMD1050 7–27 117
- 7.3.4.3 Interface Menu 118
- MN-DMD1050 7–29 119
- MN-DMD1050 7–30 120
- MN-DMD1050 7–31 121
- MN-DMD1050 7–32 122
- 7.3.4.4 Monitor Menu 123
- MN-DMD1050 7–34 124
- MN-DMD1050 7–35 125
- MN-DMD1050 7–36 126
- 7.3.4.5 Alarms Menu 127
- MN-DMD1050 7–38 128
- MN-DMD1050 129
- MN-DMD1050 7–40 130
- MN-DMD1050 7–41 131
- MN-DMD1050 7–42 132
- MN-DMD1050 7–43 133
- 7.3.4.5.1 System Menu 134
- MN-DMD1050 7–45 135
- MN-DMD1050 7–46 136
- 7.3.4.6 Test Menu 137
- Test Pattern 137
- MN-DMD1050 7–48 138
- A.1 Hardware Options 139
- A.2 Internal High-Stability 139
- A.3 Customized Options 139
- MN-DMD1050 A–2 140
- B.1 States 141
- B.2 Carrier Off 141
- B.3 Carrier On 141
- B.4 Carrier Auto 141
- B.5 Carrier VSat 142
- B.6 Carrier RTS 142
- Appendix C. TCP/IP Ethernet 143
- IMPORTANT 144
- C.4 Ethernet Test 145
- MN-DMD1050 C–4 146
- MN-DMD1050 C–5 147
- MN-DMD1050 C–6 148
- MN-DMD1050 C–7 149
- MN-DMD1050 C–8 150
- Appendix D. Web Browser 151
- Setup Guide 151
- MN-DMD1050 D–2 152
- MN-DMD1050 D–3 153
- D.4.1 Configuring the modem 154
- MN-DMD1050 D–5 155
- MN-DMD1050 D–6 156
- MN-DMD1050 D–7 157
- MN-DMD1050 D–8 158
- Appendix E.User Interface 159
- Connections 159
- MN-DMD1050 E–3 161
- 08-56-0106 162
- Appendix F.Ethernet Data 163
- Interface 163
- MN-DMD1050 F–2 164
- MN-DMD1050 F–3 165
- MN-DMD1050 F–4 166
- Figure F-4 – High Speed Mesh 167
- MN-DMD1050 F–6 168
- MN-DMD1050 F–7 169
- Prioritized Queues 170
- F.8.1 Normal QOS 171
- F.8.2 Port Based QOS 171
- F.8.3 Fair Weighted Queuing 171
- MN-DMD1050 F–10 172
- MN-DMD1050 F–12 174
- Appendix G. DMD1050 Strap 175
- Dis = Disable 176
- Procedure 179
- MN-DMD1050 H–2 180
- MN-DMD1050 H–3 181
- H.8 Monitor and Control 182
- METRIC CONVERSIONS 183
- Units of Length 183
- Temperature Conversions 183
- Units of Weight 183
Related products and manuals for Networking Radyne OM20
Networking Radyne DMD15 Operations Instructions
(201 pages)
(201 pages)
Networking Radyne OM20 Specifications
(212 pages)
(212 pages)
Networking Radyne DMD50 Operations Instructions
(237 pages)
(237 pages)
Networking Radyne OM20 Specifications
(220 pages)
(220 pages)
Networking Radyne MM200 Technical Information
(192 pages)
(192 pages)
Networking Radyne DMD20LBST Specifications
(306 pages)
(306 pages)
Networking Radyne OM20 User Manual
(100 pages)
(100 pages)
Networking Radyne DMD15L Operations Instructions
(118 pages)
(118 pages)
Networking Radyne MM200 User Manual
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 0.679 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals